Categories Garage Door DIY, Garage Door Openers

How to Program Your Liftmaster 890MAX, 893MAX or 895MAX LiftMaster Garage Door Remote in Diamond Springs, CA

Local Garage Doors is a company that specializes in the sales and installation of LiftMaster garage door openers and remotes. They offer a wide range of products to meet the needs of their customers, including both residential and commercial grade models. All of their products are of the highest quality and are backed by a manufacturer’s warranty for added peace of mind. In addition to selling and installing LiftMaster products, Local Garage Doors also provides repair and maintenance services to ensure that their customers’ garage doors are always in good working order. Whether you need a new opener or remote, or simply need to have your existing system repaired, Local Garage Doors has you covered.

LIFTMASTER 890MAX, 893MAX & 895MAX STEP BY STEP PROGRAMMING INSTRUCTIONS

STEP 1: Verifying The Color Of Your Garage Door Operators “Learn” Button
Verify the color of the “Learn” button on the garage door opener and be sure to remember the color. Follow your garage door operators antenna that hangs down from the motor head. You might have to open the light cover. Following the antenna upward will lead you to the your motors learn button.

STEP 2: Putting Remote Control Into Programming Mode
Press and hold the program button the remote control until the LED on the front of the remote control turns on.

STEP 3: Setting Remote Control To Correct Learn Button Type
Press and release the button on your remote in which you wish to use to operate the garage door the number of times that corresponds with the garage door opener type learn button color from “STEP 1”.

STEP 4: Exit Remotes Programming Mode
To exit programming mode, press any remote control button EXCEPT the button that was just programmed.

STEP 5: Getting Your Operator (Motor) Into Programming Mode
Press and release the Learn button on the garage door opener. It’s important to remember your Operator/Motors learn button could be yellow, purple, red, orange or green. Also make sure to press and release the learn button quickly. Once the learn button is pressed, you will have 30 seconds to complete the next step. DO NOT HOLD DOWN THE LEARN BUTTON; THIS WILL CLEAR OUT ALL PROGRAMMING TO YOUR OPERATOR/MOTOR.

STEP 6: Syncing New Remote Control To The Operator (Motor)
Press the remote control button we programmed in “step 3” until the garage door opener lights flash or two clicks are heard. Once lights flash or two clicks are heard, that means programming was successful.

STEP 7: Test To Confirm
To test the new remote, press the programmed button on the remote control. The garage door and operator should activate and the garage door should start moving.

STEP 8: Visor Clip
Install the visor clip (not applicable for Model 890MAX).

If you are having issues getting your remote to program, THIS VIDEO may helpful in assisting you with the programming.

Related Articles:

  1. Expert Garage Door Repair Service
  2. Reliable Garage Door Off Track Repair
  3. Expert Garage Door Torsion Spring Repair
Categories Garage Door DIY, Garage Door Remotes

Programming a Garage Door Opener: A Step-by-Step Guide

Local Garage Doors Step by step guide to program garage door opener in Pleasanton, CA

If you have a garage door opener in Pleasanton, CA, it’s important to know how to program it so that it functions properly. Fortunately, programming a garage door opener is a fairly simple process that can be done in just a few easy steps.

First, you’ll need to locate the programming button on your garage door opener. This is usually a small, red, yellow, purple or green button located near the top of the motor unit. If you’re having trouble finding it, check the owner’s manual or contact the manufacturer for assistance.

Next, press and hold the programming button until the garage door opener lights begin to flash. This usually takes about six seconds. Once the lights are flashing, release the button.

Now it’s time to program your remote control. Press and hold the “learn” or “program” button on your remote control, which is usually located near the top of the remote. At the same time, press and release the button on your garage door opener that you want to program to the remote.

The garage door opener lights should now stop flashing, indicating that the programming process is complete. Test the remote to make sure it’s working properly by pressing the button that you just programmed. If the garage door opens or closes, you’re all set!

If you’re having trouble programming your garage door opener, don’t worry. Local Garage Doors, a trusted garage door repair company in Pleasanton, CA with a 5-star rating on Yelp and Google, is here to help. Contact us for assistance with programming your garage door opener or any other garage door-related issues. Our team of experienced technicians will have your garage door working smoothly in no time.

Related Articles:

  1. 5 Common Reasons Your Garage Door Won’t Open
  2. Choosing The Right Garage Door Opener Drive System For Your Oakland, CA Home
  3. New Garage Doors: The #1 Ranked ROI Home Improvement Project in Vallejo, CA